I've been real busy with real life which cuts into my time to get online and ramble about the Bricklin's progress. I apologize for that, but rest assured progress is being made (in fact, much more than this little snippet will attest to).
OK. A long day of work followed by a long day of working on the Bricklin.
1) Distributor cap and new spark plug wires done.
2) Installed new thermostat. The previous owner installed a 160 degree one (seriously?). Back up to 180.
3) Had to drill and tap some new paths for the radiator screws. The new ones are 5/16, except the bottom left (a fun surprise if the new owner has to change out the radiator, if I sell).
4) Plugged up the valves. Now, the air will only push the doors up; gravity will let them shut (I honestly don't know why the original plan was to have them pneumatically close...)
5) Went to NAPA to pick up belts. A warning to all - DON'T BLINDLY TRUST WHAT YOU REAL ON AN INTERNET FORUM. The belts I wrote down from the Bricklin Forum were completely wrong - I had to drive home to get the old ones to verify!
6) Ordered new radiator hoses while at NAPA. They'll be here Monday, hopefully with my new air compressor and Mazda Pulse Generator.
7) Installed new belts - Power Steering, A/C, and Alternator (Smog pump has been removed - no emissions for me). After that, it was time to call it a day.
Overall, the mechanicals are almost there. I just have to reinstall the radiator and fan, dial in the carb, and hunt down any vacuum leaks (which I'm sure will be plenty). Next week I'll finalize the pneumatic system and then it's back to the interior (and my Corbeau seats should ship "first thing next week" according to the seller)!
After that, we just wait for the body panels. Hopefully the entire thing will be done by the Summer.
Showing posts with label work to be done. Show all posts
Showing posts with label work to be done. Show all posts
Sunday, February 27, 2011
Sunday, November 28, 2010
New Tools and Some More Progress...
As Black Friday is upon us, I headed to Lowe's to pick up some nuts and bolts. I have taken off the vacuum operated headlight mechanism - they are to be replaced with small air cylinders which do the same job. Might as well upgrade everything to air if I'm going this route.
After picking up some bolts, I eyed a 170+ Kohler tool kit for $100. However, I decided to hop by the Home Depot to see if they had anything better, figuring I could just hop by again and pick up this unit if necessary. Home Depot had a Husky brand 252-piece socket and wrench set on sale for only $70. Sold!
I really only need the sockets - I have a very bad habit of not putting everything back where it belongs at the end of the night. I'll be sure to be extra diligent with this one, so I won't be in a pinch when I need a certain socket.
The kit also comes with a ridiculous amount of Alan wrenches and a few regular wrenches. Not as necessary, but still nice to have. A little bit in the future I'd like to pick up some ratcheting wrenches, but for now this is more than enough tools to (hopefully) get me through the project.
On another note, the Bricklin is coming along nicely. I coated the birdcage with some POR-15 and wired up just about all of the pneumatic stuff (compressor, air lines, valves, and mose of the cylinders) and it's just about ready to plug and play. I've been holding off on buying the replacement body panels because of a possible money issue, but it looks like it's been resolved so I'll hopefully be purchasing those this week.
On another note, Terry Tanner's air headlight system features single-acting air cylinders which spring-retract. Though I have some three-way valves which could handle the headlights, I'd really like to buy some double acting cylinders so that all the air parts could operate from the same valve block. Howvers, I'd have to modify the mounting brackets and purchase some new cylinders (probably not expensive, but time consuming!). What are your thoughts?
After picking up some bolts, I eyed a 170+ Kohler tool kit for $100. However, I decided to hop by the Home Depot to see if they had anything better, figuring I could just hop by again and pick up this unit if necessary. Home Depot had a Husky brand 252-piece socket and wrench set on sale for only $70. Sold!
I really only need the sockets - I have a very bad habit of not putting everything back where it belongs at the end of the night. I'll be sure to be extra diligent with this one, so I won't be in a pinch when I need a certain socket.
The kit also comes with a ridiculous amount of Alan wrenches and a few regular wrenches. Not as necessary, but still nice to have. A little bit in the future I'd like to pick up some ratcheting wrenches, but for now this is more than enough tools to (hopefully) get me through the project.
On another note, the Bricklin is coming along nicely. I coated the birdcage with some POR-15 and wired up just about all of the pneumatic stuff (compressor, air lines, valves, and mose of the cylinders) and it's just about ready to plug and play. I've been holding off on buying the replacement body panels because of a possible money issue, but it looks like it's been resolved so I'll hopefully be purchasing those this week.
On another note, Terry Tanner's air headlight system features single-acting air cylinders which spring-retract. Though I have some three-way valves which could handle the headlights, I'd really like to buy some double acting cylinders so that all the air parts could operate from the same valve block. Howvers, I'd have to modify the mounting brackets and purchase some new cylinders (probably not expensive, but time consuming!). What are your thoughts?
Sunday, November 14, 2010
Progress.
After a long absence, finally some progress has been made on the Bricklin project. Yesterday, we removed the rear bumper to take a look at the onboard air tank, which is holding air. Unfortunately, we didn't have all the connections to hook up the pneumatics. I'll have to go to Airtronics and pick up the rest on Monday.
Since we couldn't hook up the wiring and whatnot, instead we decided to crack open the POR-15 and paint the steel safety cage (which I've been putting off for literally weeks!). Though there's still a little more to paint, the top and A-pillars are completely painted, as well as the front area right underneath the windshield.
It looks more complete now, but there's still a lot more work to go...
Since we couldn't hook up the wiring and whatnot, instead we decided to crack open the POR-15 and paint the steel safety cage (which I've been putting off for literally weeks!). Though there's still a little more to paint, the top and A-pillars are completely painted, as well as the front area right underneath the windshield.
It looks more complete now, but there's still a lot more work to go...
Tuesday, September 21, 2010
Hiatus?
Holy crap, I haven't updated since the end of June!
I haven't been as gung-ho about the Bricklin project as I should be. I could lay down the reasons, some of which are my own and others are on my partner in this project. I'm not harboring resentment, but I don't feel his work ethic is quite up to snuff.
I had a talk about this the other day with a good friend of mine. Seems I'm angrier about this than I'm letting on. I was quite angry. Sean is good at what he does but is also ridiculously unreliable.
Besides the cool Nexus gauges and body panels, every big purchase has been made for the car. It's only a matter of getting off our butts and doing the work. The problem is, my helper has become a bit flakey of late, so I'm considering alternative methods of getting this project finished.
I'm having talks with a local interior shop about helping out with the process. It seems easier to pay a bit more money up front and actually get the ball rolling.
Other than my problems, the Bricklin is coming along nicely when it gets worked on. We have the back interior panel and rear side panels completed and they actually look good. All that's left for the hatch area is the rear center console, and then we can work our way to the front (thankfully, not much work is needed on the dash!). Nearly the entire air system is ready to go.
And to think, I originally wanted to be done in August...
I haven't been as gung-ho about the Bricklin project as I should be. I could lay down the reasons, some of which are my own and others are on my partner in this project. I'm not harboring resentment, but I don't feel his work ethic is quite up to snuff.
I had a talk about this the other day with a good friend of mine. Seems I'm angrier about this than I'm letting on. I was quite angry. Sean is good at what he does but is also ridiculously unreliable.
Besides the cool Nexus gauges and body panels, every big purchase has been made for the car. It's only a matter of getting off our butts and doing the work. The problem is, my helper has become a bit flakey of late, so I'm considering alternative methods of getting this project finished.
I'm having talks with a local interior shop about helping out with the process. It seems easier to pay a bit more money up front and actually get the ball rolling.
Other than my problems, the Bricklin is coming along nicely when it gets worked on. We have the back interior panel and rear side panels completed and they actually look good. All that's left for the hatch area is the rear center console, and then we can work our way to the front (thankfully, not much work is needed on the dash!). Nearly the entire air system is ready to go.
And to think, I originally wanted to be done in August...
Wednesday, June 16, 2010
Air Hatch.
Reusing the old unit, I have successfully mounted the hatch on two air cylinders, that will convienently use the same system as the doors (and everything else involving pneumatics, for that matter). We've also found an excellent switch panel to hook up all the electronics. It's quite nice, and also features a separate unit that can be remotely mounted. It's really designed to be mounted in the engine bay to turn on such things as ground effects, but it will work perfectly for the Bricklin.
The idea is, with the press of a button the hatch will open. Press another (convienently mounted at the rear of the car) and the whole rear console will slide forward. Press one more and the storage compartments pop open. Yet another button will activate the ambient lighting. If I get in the driver's seat and realize everything isn't where it's supposed to be, I can just hit the switches from the driver's seat and set everything right again.
Speaking of the interior modifications, the newly mounted cylinders require a bit of reworking of the interior panels. Always nice to find that something doesn't quite fit as originally intended.
Other than that minor setback, everything's going well. Sorry for the lack of updates; I have another (non-automotive) project in the works that's been taking up my time when not working on the Bricklin. More on that if or when it pans out.
The idea is, with the press of a button the hatch will open. Press another (convienently mounted at the rear of the car) and the whole rear console will slide forward. Press one more and the storage compartments pop open. Yet another button will activate the ambient lighting. If I get in the driver's seat and realize everything isn't where it's supposed to be, I can just hit the switches from the driver's seat and set everything right again.
Speaking of the interior modifications, the newly mounted cylinders require a bit of reworking of the interior panels. Always nice to find that something doesn't quite fit as originally intended.
Other than that minor setback, everything's going well. Sorry for the lack of updates; I have another (non-automotive) project in the works that's been taking up my time when not working on the Bricklin. More on that if or when it pans out.
Monday, May 24, 2010
Small Stuff
Called up Bricklin Parts and Services today and ordered some of the smaller parts for the Bricklin, including new air cylinders, weatherstripping, and updated air headlight system.
It should be shipped either later today or tomorrow. We'll see when they show up.
The actual body panels are expensive to ship individually, and shipping on a pallet aparently isn't desireable. In addition, though there is a backstock available, ordering the panels requires additional stock to be produced. So, I held off ordering them for now. Basically, my options are as follows:
1) Have each panel shipped individually.
2) Fly to Virginia, rent a U-Haul truck, drive them back to Washington ourselves.
Both options are expensive; the latter will probably be just a bit less. What do you think?
It should be shipped either later today or tomorrow. We'll see when they show up.
The actual body panels are expensive to ship individually, and shipping on a pallet aparently isn't desireable. In addition, though there is a backstock available, ordering the panels requires additional stock to be produced. So, I held off ordering them for now. Basically, my options are as follows:
1) Have each panel shipped individually.
2) Fly to Virginia, rent a U-Haul truck, drive them back to Washington ourselves.
Both options are expensive; the latter will probably be just a bit less. What do you think?
Sunday, May 16, 2010
Lack of Updates...
...does not equal a lack of work or play on my part.
Work continues on the Bricklin. This week I will call Terry Tanner and order the parts; my list is as follows:
Body Panels
- Headlight covers
- Roof Panel
- Door Skins
- Hatch
- A Pillars
- Hood
- Front Fenders (still deciding on those)
Assorted Parts
- Outside Door Weatherstripping
- Inside Birdcage Weatherstripping
- New Pneumatic Cylinders
- Door (Boomerang) Braces
- Weatherstripping for the Rear Quarter Windows
- Air Headlight System
It's going to be a sizeable order, obviously, and will probably need to be shipped on a pallet. Hopefully it won't be too expensive.
I know I've said it before, but the desconstruction is nearly complete. The only body panel still attached up front is the bumper; the hood, hood extension, fenders, A-pillars, roof, hatch, and doors have all been removed. All but the hood extension (and possibly fenders, they're not too bad) will be replaced with fiberglass replacements.
We've discovered all sorts of hacked together crap going through this thing. Going through the engine bay, we found a little device with a vacuum line going to the carb and an air line headed to the compressor. With no idea what it was, we took it off for further examination. It was a non-operational vacuum operated air pump! The air doors must have been a very early conversion; they haven't used these things in years. They would serve as the main air pump and the electric compressor (that I used the entire trip home) is just there as a backup. Both will be replaced with a single heavy duty air compressor.
In other news, earlier today was the Spring Opener at XXX. I was working and didn't attend, but it is the unofficial start of the car show season (though I went to quite a few cruise nights in March and April).
Work continues on the Bricklin. This week I will call Terry Tanner and order the parts; my list is as follows:
Body Panels
- Headlight covers
- Roof Panel
- Door Skins
- Hatch
- A Pillars
- Hood
- Front Fenders (still deciding on those)
Assorted Parts
- Outside Door Weatherstripping
- Inside Birdcage Weatherstripping
- New Pneumatic Cylinders
- Door (Boomerang) Braces
- Weatherstripping for the Rear Quarter Windows
- Air Headlight System
It's going to be a sizeable order, obviously, and will probably need to be shipped on a pallet. Hopefully it won't be too expensive.
I know I've said it before, but the desconstruction is nearly complete. The only body panel still attached up front is the bumper; the hood, hood extension, fenders, A-pillars, roof, hatch, and doors have all been removed. All but the hood extension (and possibly fenders, they're not too bad) will be replaced with fiberglass replacements.
We've discovered all sorts of hacked together crap going through this thing. Going through the engine bay, we found a little device with a vacuum line going to the carb and an air line headed to the compressor. With no idea what it was, we took it off for further examination. It was a non-operational vacuum operated air pump! The air doors must have been a very early conversion; they haven't used these things in years. They would serve as the main air pump and the electric compressor (that I used the entire trip home) is just there as a backup. Both will be replaced with a single heavy duty air compressor.
In other news, earlier today was the Spring Opener at XXX. I was working and didn't attend, but it is the unofficial start of the car show season (though I went to quite a few cruise nights in March and April).
Monday, May 10, 2010
Why Do They Do This To Me?
This entry may be my most philosophical work to date. Cars are a lot like pets.
Not that I'm saying cars are ensouled. But neither animal nor automobile can tell you what is wrong themselves, even if you know something is wrong.
You can only hope, when you either take the animal to the vet or take the car to the shop (or perform the surgery yourself, in this case), the patient knows it is for the best.
Such is the case with the Bricklin. Though many body panels have been removed and the engine is inoperable, it will be for the best when the work is finished! Technically, we could just do a quick once over of the interior and be done with it, but there are so many underlying issues needing to be addressed.
I can either do it right or end up having to do it again.
So I'll take the extra steps to make it so. We'll strip all the body panels off and apply POR-15 to the safety cage and frame to prevent it from rusting again. We'll take the doors apart and weld reinforcement bars where recommended. We'll run through the entire pneumatic system, replacing the compressor, air lines, and even the cylinders which raise and lower the doors.
We can rebuilt it. We have the technology.
Bear in mind this photo was taken a few days ago (there is always some lag time between any photo op and my blogging). The roof has been sanded down to bare metal (mostly on the driver's side, however) and should be complete within the week.
We're still working on the custom interior. It's coming along, slowly but surely. The rear console now moves under its own power (with a little help from an air compressor). Interior fabric will be ordered shortly, along with more carpet, since we misjudged the amount needed. The carpet I have now is just enough to cover the floors in the foot wells.
With mistakes like those, you really have to hope the Bricklin has faith in my ability.
Not that I'm saying cars are ensouled. But neither animal nor automobile can tell you what is wrong themselves, even if you know something is wrong.
You can only hope, when you either take the animal to the vet or take the car to the shop (or perform the surgery yourself, in this case), the patient knows it is for the best.
Such is the case with the Bricklin. Though many body panels have been removed and the engine is inoperable, it will be for the best when the work is finished! Technically, we could just do a quick once over of the interior and be done with it, but there are so many underlying issues needing to be addressed.
I can either do it right or end up having to do it again.
So I'll take the extra steps to make it so. We'll strip all the body panels off and apply POR-15 to the safety cage and frame to prevent it from rusting again. We'll take the doors apart and weld reinforcement bars where recommended. We'll run through the entire pneumatic system, replacing the compressor, air lines, and even the cylinders which raise and lower the doors.
We can rebuilt it. We have the technology.
Bear in mind this photo was taken a few days ago (there is always some lag time between any photo op and my blogging). The roof has been sanded down to bare metal (mostly on the driver's side, however) and should be complete within the week.
We're still working on the custom interior. It's coming along, slowly but surely. The rear console now moves under its own power (with a little help from an air compressor). Interior fabric will be ordered shortly, along with more carpet, since we misjudged the amount needed. The carpet I have now is just enough to cover the floors in the foot wells.
With mistakes like those, you really have to hope the Bricklin has faith in my ability.
Tuesday, May 4, 2010
May the Fourth be With You...
Yeah, lame pun of the day. You can thank "itschrome" at the Cadillac Forums for that one.
Because I need extra space in the garage to accomodate work area needed for the Bricklin, the Allante has unfortunately been sitting outside under a car cover. The car cover is a very nice waterproof yet breathable model, and fits the Allante nicely (if not perfectly). It fits so good I decided not to tie it down to the underside, letting it just sit atop the car.
You probably can see where this is going...
That move bit me in the ass. Yesterday, I left to find the cover had blown off my poor convertible in the pouring rain. Thankfully, the top was up (I actually flirted with the idea of leaving the top down, THAT would have been a catastrophe) but the very back wasn't latched. Plus, the top leaks in heavy rain, so I was very worried I would find a pool when I opened the door. Thankfully, other than the car being wet and a little rain that snuck through the unlatched top into the boot, all is OK. I've learned my lesson.
In another "Holy Hell" moment, I've been shopping around for the Nexus gauges I talked about last time. They are EXPENSIVE. And expensive for me, with my steady job and hefty paychecks, is more than your average Joe. They're going to be at least a grand.
Originally, I wanted to get in and done with this car for under $10,000. It's becoming more and more clear I will not hit this number. Replacement body panels alone will be pushing $2,500. So, in classic form, I'm just lowering my standards and raising my budget by a couple thousand dollars.
Because I need extra space in the garage to accomodate work area needed for the Bricklin, the Allante has unfortunately been sitting outside under a car cover. The car cover is a very nice waterproof yet breathable model, and fits the Allante nicely (if not perfectly). It fits so good I decided not to tie it down to the underside, letting it just sit atop the car.
You probably can see where this is going...
That move bit me in the ass. Yesterday, I left to find the cover had blown off my poor convertible in the pouring rain. Thankfully, the top was up (I actually flirted with the idea of leaving the top down, THAT would have been a catastrophe) but the very back wasn't latched. Plus, the top leaks in heavy rain, so I was very worried I would find a pool when I opened the door. Thankfully, other than the car being wet and a little rain that snuck through the unlatched top into the boot, all is OK. I've learned my lesson.
In another "Holy Hell" moment, I've been shopping around for the Nexus gauges I talked about last time. They are EXPENSIVE. And expensive for me, with my steady job and hefty paychecks, is more than your average Joe. They're going to be at least a grand.
Originally, I wanted to get in and done with this car for under $10,000. It's becoming more and more clear I will not hit this number. Replacement body panels alone will be pushing $2,500. So, in classic form, I'm just lowering my standards and raising my budget by a couple thousand dollars.
Monday, April 19, 2010
With the teardown complete, the buildup BEGINS!
With little exception, the Bricklin floor pan is now completely devoid of any last remnants of old carpet. My new carpet arrived a few days ago, it was picked up along with two big sheets of wood that will serve as the base and frame of the rear console.
I painstakingly removed the vinyl upholstery from the interior rear quarter panels and console. The left side turned out to be broken by the rear window, but it's repairable. We're also busy mocking up little subwoofer boxes and other interior trim before we begin actual fiberglass work.
We made a trip to CarNutz (next to Park Place Ltd. in Bellevue, WA) to pick out interior fabric. We're going with a black and grey color scheme, black vinyl with grey suede. We'll order two types of suede but both the same color - one that has a weave pattern and the other with no pattern to give the interior some diversity.
In other news, the carburetor was farmed out to Carb Connection in Kirkland. It was literally dropped off one day and picked up the next. It should be as good as a new unit. Though I played with the idea of upgrading to a four barrel carb and intake, I decided just to stay with the two barrel set up, as I won't have the fret with hood clearance
The smog pump has been removed, since emissions will no longer be tested (collector plates FTW!). This should free up some power from the motor.
I've picked out a suitable shift from Lokar Performance and will order it shortly. I've also sent out an e-mail to Terry Tanner (a god amongst Bricklin owners) about ordering some replacement body panels, but have yet to hear back. I guess that's what happens when you e-mail a business on Sunday and expect an answer back Monday morning; I'm sure he'll get back to me.
To have the needed extra space in the garage, the Allante has unfortunately been moved to the driveway, underneath a car cover. I'm beginning the think it's jealous; I wanted to drive it to pick up the carburetor, but it wouldn't crank! After some time, it did eventually start. My semi-professional diagnosis is the car is green with envy.
I painstakingly removed the vinyl upholstery from the interior rear quarter panels and console. The left side turned out to be broken by the rear window, but it's repairable. We're also busy mocking up little subwoofer boxes and other interior trim before we begin actual fiberglass work.
We made a trip to CarNutz (next to Park Place Ltd. in Bellevue, WA) to pick out interior fabric. We're going with a black and grey color scheme, black vinyl with grey suede. We'll order two types of suede but both the same color - one that has a weave pattern and the other with no pattern to give the interior some diversity.
In other news, the carburetor was farmed out to Carb Connection in Kirkland. It was literally dropped off one day and picked up the next. It should be as good as a new unit. Though I played with the idea of upgrading to a four barrel carb and intake, I decided just to stay with the two barrel set up, as I won't have the fret with hood clearance
The smog pump has been removed, since emissions will no longer be tested (collector plates FTW!). This should free up some power from the motor.
I've picked out a suitable shift from Lokar Performance and will order it shortly. I've also sent out an e-mail to Terry Tanner (a god amongst Bricklin owners) about ordering some replacement body panels, but have yet to hear back. I guess that's what happens when you e-mail a business on Sunday and expect an answer back Monday morning; I'm sure he'll get back to me.
To have the needed extra space in the garage, the Allante has unfortunately been moved to the driveway, underneath a car cover. I'm beginning the think it's jealous; I wanted to drive it to pick up the carburetor, but it wouldn't crank! After some time, it did eventually start. My semi-professional diagnosis is the car is green with envy.
Friday, April 9, 2010
Bricklin Interior Sketches.
I AM NOT AN ARTIST. The pictures you are about to see are conceptual works to help envision how the Bricklin interior eventually will turn out. They are not drawn to scale or with any sense of professionalism. They are merely visual aids to reference. And they are NOT set in stone.
Perhaps some exposition is needed. The first sketch would be a head on view of the cockpit, as if you were looking at the picture from the dash of the car. We plan to extend the console so that it will "flow" into the hatch area. Note the "Stylized B" - this is an approximation of the Bricklin logo.
The second sketch is an overhead view of the interior, the top being the dash and the very bottom being the hatch area. Note the area behind the seats: this is will be the extension of the console. The exterior B-pillar has three styling louvers; we will duplicate these to add some flair to the design (they will also be integrated in the ceiling very discreetly - the hope is the average looky-lou won't notice). It's hard to put into words, but the area (as marked right and left of the faux louvers) will break away from the center section using the same curve as the dash. We could possibly make those areas some covered storage - I'm thinking of adding in compartments that open much like the gullwing doors. Just another nod to the Bricklin styling.
Those familiar with the car will note this section will be placed directly on top of the battery compartment, disallowing access. The entire unit will move further back into the hatch, allowing access when needed. Since a sizeable air tank is already on board to open the doors, this too will operate using pneumatics! This piece will slide above the smaller piece mounted at the rear of the hatch (this has also been designed to somewhat resemble the front bumper).
I'm still undecided on how the side compartments will flow into the wheel arches; they have been left unfinished for the time being.
Of course, it's hard to tell exactly what's going on in my mind by just looking at these rough sketches. But this will just help show you where the project is heading.
One Week Vacation. Zero Work Done.
This past week I have been on vacation. I had plenty of time to work on the Bricklin, and made arrangements with Sean (my buddy who is helping with this restoration) to take a few days and make some real progress.
Instead, I've been playing BioShock the last few days.
It's a story. At the beginning of the week, Sean was sick. Then, I caught the same damn illness. The sore throat and vicious cough weren't debilitating, but were severe enough that I had absolutely no work ethic for the project. I'm finally beginning to feel better, and I really want to keep this project moving. I don't want this to become one of those blogs aborted halfway through, or worse yet have this project take years to finish.
Where it stands now:
- I did make some rough sketches of what the interior will end up looking like. Last week, we brainstormed and came up with a general direction for the interior. The plan is to modernize the Bricklin's interior while remaining true to the original design aesthetic. In effect, making it look as though it was designed for the car yesterday. It's certainly ambitious, but I have been assured it A) completely doable and B) fairly simple (at least compared to some things we could be doing).
- I'm not entirely sure of the interior color scheme. I'm thinking black and a charcoal grey two-tone arrangement. I'm also putting some real thought into adding white into the mix, to match the exterior color.
- Carpet has been ordered.
- Mechanically, I'm in a good position. To get the thing running again, all I really need to do is hook up a new carburetor (EDIT: And one faulty vacuum connection). I'm weighing the pros and cons between a 4 barrel and a 2 barrel. The hood doesn't leave much room for clearance; I've heard I'll need to buy a drop base air cleaner to fit in the former.
Seriously, the car will be absolutely sick when it's finished. The only question is, when will it be done? My original August "deadline" is only five months away, and I am having some serious doubts that it will be ready to drive in time. I'll work on scanning my hand drawn design, until then, your imagination will have to suffice.
Instead, I've been playing BioShock the last few days.
It's a story. At the beginning of the week, Sean was sick. Then, I caught the same damn illness. The sore throat and vicious cough weren't debilitating, but were severe enough that I had absolutely no work ethic for the project. I'm finally beginning to feel better, and I really want to keep this project moving. I don't want this to become one of those blogs aborted halfway through, or worse yet have this project take years to finish.
Where it stands now:
- I did make some rough sketches of what the interior will end up looking like. Last week, we brainstormed and came up with a general direction for the interior. The plan is to modernize the Bricklin's interior while remaining true to the original design aesthetic. In effect, making it look as though it was designed for the car yesterday. It's certainly ambitious, but I have been assured it A) completely doable and B) fairly simple (at least compared to some things we could be doing).
- I'm not entirely sure of the interior color scheme. I'm thinking black and a charcoal grey two-tone arrangement. I'm also putting some real thought into adding white into the mix, to match the exterior color.
- Carpet has been ordered.
- Mechanically, I'm in a good position. To get the thing running again, all I really need to do is hook up a new carburetor (EDIT: And one faulty vacuum connection). I'm weighing the pros and cons between a 4 barrel and a 2 barrel. The hood doesn't leave much room for clearance; I've heard I'll need to buy a drop base air cleaner to fit in the former.
Seriously, the car will be absolutely sick when it's finished. The only question is, when will it be done? My original August "deadline" is only five months away, and I am having some serious doubts that it will be ready to drive in time. I'll work on scanning my hand drawn design, until then, your imagination will have to suffice.
Monday, March 29, 2010
Shaving the Mammoth
The Bricklin teardown is nearing completion. The interior is completed, and the only thing remaining in the car is the dash. All that's left to do is shave the mammoth. No, it's not some innuendo.
After the carpet and soundproofing material was removed, the adhesive left some residue on the floarboards. It can best be described as having the same texture of a wooly mammoth. It is nasty. To get it off, I have to take a putty knife and literally scrape down to the fiberglass. Thus is born the phrase "Shaving the Mammoth." The hatch and driver floorpan is mostly done; I'll go out later today and scrape the passenger area and do a quick once over to get anything I missed.
With that finished, we can begin reassembly. My partner in crime, Sean, and I have already come up with some sweet ideas of where we want this project to go. It's going to be sweet when it's done, but right now it's far from.
After the carpet and soundproofing material was removed, the adhesive left some residue on the floarboards. It can best be described as having the same texture of a wooly mammoth. It is nasty. To get it off, I have to take a putty knife and literally scrape down to the fiberglass. Thus is born the phrase "Shaving the Mammoth." The hatch and driver floorpan is mostly done; I'll go out later today and scrape the passenger area and do a quick once over to get anything I missed.
With that finished, we can begin reassembly. My partner in crime, Sean, and I have already come up with some sweet ideas of where we want this project to go. It's going to be sweet when it's done, but right now it's far from.
Friday, March 19, 2010
Operation: Teardown
The Bricklin is now in pieces, and receiving its refurbishing on Overhaulin: Garage Edition.
Yesterday, we tore out the side interior hatch panels, back panel, headliner, center console, seats (conveniently sharing rails with a Jeep CJ-5), and various assorted teardown. The interior is now but a shell, with only the dash and steering wheel remaining in place.
In February I told of how, on the return trip from California, the Bricklin leaked water. Though I did my best to dry the affected interior, once the seats and carpet was removed, I uncovered a small puddle remaining. Good thing the floor is fiberglass!
Now begins the arduous task of removing the residue left from the carpet adhesive, and scraping the floor down to bare fiberglass. The hatch area was mostly done last night, but the rest of the car remains. Once that is done, we can install new carpet.
After the day is done, the interior is bare and the car is undriveable. This is the toughest part of the restoration, in my opinion. It is so far from being completed, and I know I have only myself to blame for tearing it apart. It is disheartening, but the negative now should lead to positive dividends in the future, when the car is nearing completion.
Yesterday, we tore out the side interior hatch panels, back panel, headliner, center console, seats (conveniently sharing rails with a Jeep CJ-5), and various assorted teardown. The interior is now but a shell, with only the dash and steering wheel remaining in place.
In February I told of how, on the return trip from California, the Bricklin leaked water. Though I did my best to dry the affected interior, once the seats and carpet was removed, I uncovered a small puddle remaining. Good thing the floor is fiberglass!
Now begins the arduous task of removing the residue left from the carpet adhesive, and scraping the floor down to bare fiberglass. The hatch area was mostly done last night, but the rest of the car remains. Once that is done, we can install new carpet.
After the day is done, the interior is bare and the car is undriveable. This is the toughest part of the restoration, in my opinion. It is so far from being completed, and I know I have only myself to blame for tearing it apart. It is disheartening, but the negative now should lead to positive dividends in the future, when the car is nearing completion.
Friday, March 12, 2010
Wednesday Night's Bricklin Overview
A late night Wednesday led to ripping out a lot of botch-job wiring from the Bricklin, including an inoperable alarm system and the world's most ghetto radio (a detachable faceplate unit from the 80s!). My original list of work was only 13 items long. It nearly doubled overnight.
Removal of the carburetor revealed it was uncontrollably dumping fuel into the engine with blatant disregard if it was actually needed. This was flooding the engine. Diagnosis: A bad carburetor. I could opt for a rebuilt, but the original plan was to replace the stock two barrel with a four barrel (if the original timeline called for action much later in the process). It will have to be done sooner.
Further inspection revealed the onboard air pump for the doors was originally meant for air shocks. Not exactly heavy duty equipment (though it explains why it takes nearly twenty minutes to pump the system to 120 psi). Whoever installed the pneumatic system didn’t sweat the details. A heavy duty compressor, new air lines (possibly), and a pressure regulator should make the system dependable.
The new Bricklin work list sits at 25 individual items, TWO of which are finished. Most are small fixes, so it should get whittled down quickly to the imperative items fairly quickly. There’s no rush; I’d like to have it done by August, but that’s not an absolute deadline. Hopefully work will move quickly and I’ll be behind the wheel by then.
Removal of the carburetor revealed it was uncontrollably dumping fuel into the engine with blatant disregard if it was actually needed. This was flooding the engine. Diagnosis: A bad carburetor. I could opt for a rebuilt, but the original plan was to replace the stock two barrel with a four barrel (if the original timeline called for action much later in the process). It will have to be done sooner.
Further inspection revealed the onboard air pump for the doors was originally meant for air shocks. Not exactly heavy duty equipment (though it explains why it takes nearly twenty minutes to pump the system to 120 psi). Whoever installed the pneumatic system didn’t sweat the details. A heavy duty compressor, new air lines (possibly), and a pressure regulator should make the system dependable.
The new Bricklin work list sits at 25 individual items, TWO of which are finished. Most are small fixes, so it should get whittled down quickly to the imperative items fairly quickly. There’s no rush; I’d like to have it done by August, but that’s not an absolute deadline. Hopefully work will move quickly and I’ll be behind the wheel by then.
Sunday, March 7, 2010
Work Begins...
I knew the Bricklin wouldn't be completely perfect and that work would need to be done. I've compiled a list of both mechanical and cosmetic issues that need to be addressed. Most are minor things like fluid changes.
A recent overview of the engine (necessitated by an intermittent stall) revealed three more items to add:
1) The water pump is failing. It is not leaking, but it is obvious something is not right inside.
2) The intake manifold gasket is shot.
3) I have a vacuum leak somewhere that needs to be addressed, most likely causing the engine to stall.
These have now become my top priority. They will be dealt with promptly.
In other news, I've been driving the Allante the last few days. The hardtop was removed yesterday, and it's ready for Spring/Summer 2010.
A recent overview of the engine (necessitated by an intermittent stall) revealed three more items to add:
1) The water pump is failing. It is not leaking, but it is obvious something is not right inside.
2) The intake manifold gasket is shot.
3) I have a vacuum leak somewhere that needs to be addressed, most likely causing the engine to stall.
These have now become my top priority. They will be dealt with promptly.
In other news, I've been driving the Allante the last few days. The hardtop was removed yesterday, and it's ready for Spring/Summer 2010.
Subscribe to:
Posts (Atom)


